While it may seem like a good plan to own the best nail gun, its efficacy and level of usage must be measured before purchase. A simple hammer is more than enough for driving nails destined for hanging picture frames and paintings. On the other hand, construction and building projects will require the use of a powerful nail gun that can get the job done quickly and proficiently. The biggest good thing about victimization this tool is its ability to quickly shoot varied nails at intervals seconds and insert into the foremost resilient construction materials like actual, plywood, and hardwood panels. This Buzzle nail gun shopping for guide discusses a way to select a nail gun and a few factors to contemplate.
Stick- and Coil-shaped Nail Guns
Nail guns are set up in two shapes, the first being stick-shaped and the other being coiled. A stick nail gun has a directly and long magazine that is meant for holding a strip of nails. Stick guns may come in both oblique and straight setups whereas the angled models have a thicker weight. On the other hand, coiled nail guns are prepared with a cylindrical magazine in which the nails are rolled up.
Brad Nail Guns
A brad nail gun comprises fine weigh nails. Such a nail gun is destined for being used on baseboards, cabinets, thin trims, and moldings. These guns carry nails that are ⅝-2″ long and have small heads.
Finish Nail Guns
Finish nail guns have a heavier 14-16 gauge wire and are handy for baseboards, trim work, paneling and smaller crowns, and center molding. This type of nail gun has the ability to hold and shoot 2½-inch long nails and leaves a bigger hole than a brad nailer.
Framing nailer guns are intended for heavy-duty framing during construction of houses and buildings. They exploit low-gauge nails that are held together to form an attack that must be slid into the magazine of the nail gun. Such magazines have the ability to hold the huge amount of 20-40 inch stick nails.
Roofing nailers are prepared with wide-headed and shorter nails. This type of nail gun is ideal for roofing, wall sheathing, framing, and underlayment. The nails are fitted into a coil-shaped magazine. A roofing nail comes with a dual contact trigger that aids in rapid shooting and embedding of coil nails.
Factors to Consider while Buying Nail Guns
Use of Air Compressor
Pneumatic nail guns would require the employment of a strong compressor with adequate pounds per square measure (PSI) to stay the tool running at its expected pace. Therefore, check the air requirement of the pneumatic nail gun so as to not fall short of adequate pressure while working on a project. Additionally, these power tools need optimal air volume, which is measured in cubic feet per minute (CFM). Thus, to maintain appropriate CFM, make sure you buy the right-sized air hose for the compressor and keep it clean, dry, and the flow of air unrestricted. Make positive that the nail gun has a PSI and CFM rating that is compatible with that of the air mechanical device you would like to get or already own.
Cordless nail guns do not need an air compressor to rely on. Instead, these nailers use flammable gas, which is drained into the gun’s combustion chamber from a 0.6-oz. fuel cartridge. These gas nailers are powered by a battery that is rechargeable and uses a linear-drive motor. Once the trigger is applied, the battery causes the gas to ignite, thereby, releasing enough energy to drive the piston and release a nail. though not as powerful as air compressor driven nail guns, conductor nail guns ar nearly as powerful and fast. However, these nailers are far easier to use in tight spaces, needless start-up time, and are more variable than pneumatic nailers.
There ar completely different trigger mechanisms offered for nail guns these days. Therefore, you’ll attempt the tool before choosing one specific mechanism. For instance, some nail guns require that the user holds down the trigger and tap the gun on the nailing surface to release the fastener. Some nailers shoot nails at the slightest press of the trigger, which may end up releasing unwanted nails on the nailing surface. The best and the safest option is to opt for a nail gun that has multiple trigger settings, that enable the user to select whichever is a lot of comfy to use and meet the firing wants of a specific project.
It is imperative that the nail gun you opt for has adjustable depth options thus that you might be in a position to management the depth at that the fastener reaches the nailing surface. This setting will help you avoid nail protrusion, deep pecker markings, and countersinking of fasteners.
The weight of the nail gun will determine how comfortable, stable, and easy it is for you to use. For a safer bet, opt for a nail gun with a magnesium and aluminum alloy body, as these materials aid in drastically reducing the overall weight of the tool. Secondly, these materials also contribute in preventing the machine from overheating.
Being an extremely dangerous tool, it is of utmost importance that you choose a nail gun that is comfortable for you to use. choose for an ergonomic design that will help balance the weight of the tool and make it easier to grip. choose for a nail gun that has a big trigger and safety lock so that you never accidentally press the trigger.
Nail guns may release a lot of exhaust and surface dust while being used. The exhaust plate in the gun ensures that the exhaust is diverted and does not cause discomfort to the user. You might enhance this feature by selecting a nail gun with adjustable exhaust plates that will be pointed even additional away from the user.
Pneumatic nail guns have to be compelled to be oiled often to stay the tool functioning optimally. Adding a few drops of tool oil in the nail gun’s air inlet will prevent nails from jamming.
Lastly, you must buy a safety box/case to store the nail gun, so as to protect it from show off and tear and prevent accidental injuries.